View TC1040_590447.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

TC1040
Linear Building Block - Dual Low Power Comparator and Voltage Reference with Shutdown
Features
* Combines Two Comparators and a Voltage Reference in a Single Package * Optimized for Single Supply Operation * Small Package: 8-Pin MSOP * Ultra Low Input Bias Current: Less than 100pA * Low Quiescent Current, Operating: 10A (Typ.) Shutdown Mode: 6A (Typ.) * Rail-to-Rail Inputs and Outputs * Operates Down to VDD = 1.8V * Reference and One Comparator Remain Active in Shutdown to Provide Supervisory Functions
General Description
The TC1040 is a mixed-function device combining two comparators and a voltage reference in a single 8-pin package. The inverting input of Comparator A and the non-inverting input of Comparator B are internally connected to the reference. This increased integration allows the user to replace two packages, which saves space, lowers supply current and increases system performance. The TC1040 operates from two 1.5V alkaline cells down to VDD = 1.8V. It requires only 10A typical of supply current, which significantly extends battery life. A low power shutdown input (SHDN) disables one of the comparators, placing its outputs in a high-impedance state. This mode saves battery power and allows comparator outputs to share common analog lines (multiplexing). Shutdown current is 6A (typical). Rail-to-rail inputs and outputs allow operation from low supply voltages with large input and output signal swings. Packaged in an 8-Pin MSOP, the TC1040 is ideal for applications requiring low power level detection. Temperature Range -40C to +85C
OUTA 1
Applications
* * * * Power Supply Circuits Battery Operated Equipment Consumer Products Replacements for Discrete Components
Device Selection Table
Part Number TC1040CEUA Package 8-Pin MSOP
Functional Block Diagram
TC1040
8 OUTB
Package Type
8-Pin MSOP
OUTA VSS INA+ INB1 2 3 4 8 7 OUTB VDD REF
INB4 VSS INA+ 3 Voltage Reference 5 SHDN VSS 2 A - - + B + 6 REF 7 VDD
TC1040CEUA
6 5
SHDN
2002 Microchip Technology Inc.
DS21345B-page 1
(c)
TC1040
1.0 ELECTRICAL CHARACTERISTICS
*Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions above those indicated in the operation sections of the specifications is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability.
ABSOLUTE MAXIMUM RATINGS*
Supply Voltage ......................................................6.0V Voltage on Any Pin .......... (V SS - 0.3V) to (VDD + 0.3V) Junction Temperature....................................... +150C Operating Temperature Range............. -40C to +85C Storage Temperature Range .............. -55C to +150C
TC1040 ELECTRICAL SPECIFICATIONS
Electrical Characteristics: Typical values apply at 25C and VDD = 3.0V. Minimum and maximum values apply for TA = -40 to +85C and VDD = 1.8V to 5.5V, unless otherwise specified. Symbol VDD IQ ISHDN VIH VIL ISI Comparators ROUT(SD) COUT(SD) TSEL TDESEL VIR VOS IB VOH VOL PSRR ISRC Output Resistance in Shutdown Output Capacitance in Shutdown Select Time (For Valid Output) Deselect Time Input Voltage Range Input Offset Voltage Input Bias Current Output High Voltage Output Low Voltage Power Supply Rejection Ratio Output Source Current 20 -- -- -- VSS - 0.2 -5 -5 -- VDD - 0.3 -- 60 1 -- -- 20 500 -- -- -- -- -- -- -- -- 5 -- -- VDD + 0.2 +5 +5 100 -- 0.3 -- -- M pF sec nsec V mV pA V V dB mA VDD = 3V, TA = 25C TA = -40C to 85C TA = 25C, INA+, INB- = VDD to VSS RL = 10k to VSS RL = 10k to VDD TA = 25C VDD = 1.8V to 5V INA+ = VDD , INB- = VSS Output Shorted to VSS VDD = 1.8V INA+ = VSS, INB- =VDD, Output Shorted to VDD VDD = 1.8V 100mV Overdrive, CL = 100pF 10mV Overdrive, CL = 100pF SHDN = VSS, COMPB only SHDN = VSS, COMPB only (SHDN = VIH to VOUT) RL =10k to VSS, COMPB only (SHDN = VIL to VOUT) RL =10k to VSS, COMPB only Parameter Supply Voltage Supply Current Operating Supply Current, Shutdown Input High Threshold Input Low Threshold Shutdown Input Current Min 1.8 -- -- 80% VDD -- -- Typ -- 10 0.05 -- -- -- Max 5.5 15 0.1 -- 20% VDD 100 Units V A A V V nA All outputs unloaded, SHDN = VDD SHDN = VSS Test Conditions
Shutdown Input
ISINK
Output Sink Current
2
--
--
mA
tPD1 tPD2 VREF IREF(SINK) CL(REF) EVREF eVREF
Response Time Response Time Reference Voltage Sink Current Load Capacitance Voltage Noise Noise Density
-- -- 1.176 50 50 -- -- --
4 6 1.200 -- -- -- 20 1.0
-- -- 1.224 -- -- 100 -- --
sec sec V A A pF VRMS
Voltage Reference IREF(SOURCE) Source Current
100Hz to 100kHz
V/Hz 1kHz
(c)
DS21345B-page 2
2002 Microchip Technology Inc.
TC1040
2.0 PIN DESCRIPTION
The description of the pins are listed in Table 2-1.
TABLE 2-1:
Pin No. (8-Pin MSOP) 1 2 3 4 5 6 7 8
PIN FUNCTION TABLE
Symbol OUTA VSS INA+ INBSHDN REF VDD OUTB Comparator output. Negative power supply. Non-inverting input to Comparator A. Inverting input to Comparator B. Shutdown input. Voltage reference output. Positive power supply. Comparator output. Description
2002 Microchip Technology Inc.
DS21345B-page 3
(c)
TC1040
3.0 DETAILED DESCRIPTION 4.0 TYPICAL APPLICATIONS
The TC1040 is one of a series of very low power, linear building block products targeted at low voltage, single supply applications. The TC1040 minimum operating voltage is 1.8V and typical supply current is only 10A (fully enabled). It combines two comparators and a voltage reference in a single package. A shutdown mode is incorporated for easy adaptation to system power management schemes. During shutdown, one comparator is disabled (i.e., powered down with output at a high impedance). The "still awake" comparator and voltage reference can be used as a wake-up timer, power supply monitor, LDO controller or other continuous duty circuit function. The TC1040 lends itself to a wide variety of applications, particularly in battery powered systems. It typically finds application in power management, processor supervisory and interface circuitry.
4.1
Wake-Up Timer
3.1
Comparators
Many microcontrollers have a low-power "sleep" mode that significantly reduces their supply current. Typically, the microcontroller is placed in this mode via a software instruction, and returns to a fully-enabled state upon reception of an external signal ("wake-up"). The wakeup signal is usually supplied by a hardware timer. Most system applications demand that this timer have a long duration (typically seconds or minutes), and consume as little supply current as possible. The circuit shown in Figure 4-1 is a wake-up timer made from Comparator A. (Comparator A is used because the wake-up timer must operate when SHDN is active.) Capacitor C1 charges through R1 until a voltage equal to V R is reached, at which point the "wake-up" is driven active. Upon wake-up, the microcontroller resets the timer by forcing a logic low on a dedicated, open drain I/O port pin. This discharges C1 through R4 (the value of R4 is chosen to limit maximum current sunk by the I/O port pin). With a 3V supply, the circuit as shown consumes typically 8A and furnishes a nominal timer duration of 25 seconds.
The TC1040 contains two comparators. The comparator's input range extends beyond both supply voltages by 200mV and the outputs will swing to within several millivolts of the supplies, depending on the load current being driven. The inverting input of Comparator A and the non-inverting input of Comparator B are internally connected to the output of the voltage reference. The comparators exhibit a propagation delay and supply current which are largely independent of supply voltage. The low input bias current and offset voltage make them suitable for high impedance precision applications. Comparator B is disabled during shutdown and has a high impedance output. Comparator COMPA remains active.
FIGURE 4-1:
R4
WAKE-UP TIMER
Microcontroller
3.2
Voltage Reference
R1 5M
I/O* VDD 1/2 VDD COMPA + C1 10F VR Wake-Up -
A 2.0 percent tolerance, internally biased, 1.20V bandgap voltage reference is included in the TC1040. It has a push-pull output capable of sourcing and sinking 50A. The voltage reference remains fully enabled during shutdown.
3.3
Shutdown Input
SHDN at VIL disables one comparator. The SHDN input cannot be allowed to float; when not used, connect it to VDD. The disabled comparator's output is in a high impedance state when shutdown is active. The disabled comparator's inputs and outputs can be driven from rail-to-rail by an external voltage when the TC1040 is in shutdown. No latchup will occur when the device is driven to its enabled state when SHDN is set to VIH.
TC1040
*Open Drain Port Pin
(c)
DS21345B-page 4
2002 Microchip Technology Inc.
TC1040
4.2 Precision Battery Monitor
3. Calculate RA as follows: Figure 4-2 is a precision battery low/battery dead monitoring circuit. Typically, the battery low output warns the user that a battery dead condition is imminent. Battery dead typically initiates a forced shutdown to prevent operation at low internal supply voltages (which can cause unstable system operation). The circuit in Figure 4-2 uses a single TC1040, onehalf of a TC1029, and only six external resistors. COMPA and COMPB provide precision voltage detection using VR as a reference. Resistors R2 and R4 set the detection threshold for BATT LOW, while Resistors R1 and R7 set the detection threshold for BATT FAIL. The component values shown assert BATT LOW at 2.2V (typical) and BATT FAIL at 2.0 (typical). Total current consumed by this circuit is typically 22A at 3V. Resistors R5 and R6 provide hysteresis for comparators COMPA and COMPB, respectively.
EQUATION 4-1:

VH Y R A = R C ---------VD D 4. 5.

Choose the rising threshold voltage for VSRC (VTHR). Calculate RB as follows:
EQUATION 4-2:
1 R B = ---------------------------------------------------------V THR 1-1 -------------------- - ------ ------V R x R A R A RC 6. Verify the formulas: VSRC rising: threshold

voltages
with
these
4.3
External Hysteresis (Comparator)
EQUATION 4-3:

VSRC falling:
1.
2.
2002 Microchip Technology Inc.
DS21345B-page 5

Choose the feedback resistor RC. Since the input bias current of the comparator is at most 100pA, the current through RC can be set to 100nA (i.e., 1000 times the input bias current) and retain excellent accuracy. The current through RC at the comparator's trip point is VR / R C where VR is a stable reference voltage. Determine the hysteresis voltage (VHY) between the upper and lower thresholds.
EQUATION 4-4:
V THF = V THR - R A x V DD -----------------------RC

Hysteresis can be set externally with two resistors using positive feedback techniques (see Figure 4-3). The design procedure for setting external comparator hysteresis is as follows:
1 1 1 V TH R = ( V R ) ( R A ) ------ + ------- + ------RA RB RC
(c)
TC1040
FIGURE 4-2: PRECISION BATTERY MONITOR
To System DC/DC Converter VDD TC1034 + AMP1 - R2, 330k, 1% + COMPA - BATTLOW R4, 470k, 1% R5, 7.5M VDD
3V Alkaline
+ VDD
TC1040
R1, 270k, 1% VR - COMPB + BATTFAIL
R6, 7.5M R3, 470k, 1%
FIGURE 4-3:
COMPARATOR EXTERNAL HYSTERESIS CONFIGURATION
RC
TC1040
RA VSRC
VDD + - COMPA 1/2
VOUT
RB VR
(c)
DS21345B-page 6
2002 Microchip Technology Inc.
TC1040
5.0
Note:
TYPICAL CHARACTERISTICS
The graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore outside the warranted range.
Comparator Propagation Delay vs. Supply Voltage
7 DELAY TO RISING EDGE (sec) 6 Overdrive = 10mV DELAY TO FALLING EDGE (sec)
TA = 25C CL = 100pF
Comparator Propagation Delay vs. Supply Voltage
7 6 DELAY TO RISING EDGE (sec)
TA = 25C CL = 100pF
Comparator Propagation Delay vs. Temperature
7 Overdrive = 100mV 6
Overdrive = 10mV
5 4
5 4 Overdrive = 100mV Overdrive = 50mV
5
VDD = 5V VDD = 4V
3 2 1.5 2 2.5 3
Overdrive = 50mV
3 2
4
VDD = 2V VDD = 3V
3 1.5 2 2.5 3 3.5 4 4.5 5 5.5 -40C 25C SUPPLY VOLTAGE (V)
3.5
4
4.5
5
5.5
85C
SUPPLY VOLTAGE (V)
TEMPERATURE (C)
Comparator Propagation Delay vs. Temperature
7 DELAY TO FALLING EDGE (sec) Overdrive = 100mV 6 VDD - VOUT (V)
VDD = 5V
Comparator Output Swing vs. Output Source Current
2.5 2.0
VDD = 3V VDD = 1.8V
TA = 25C
Comparator Output Swing vs. Output Sink Current
2.5 2.0 VOUT - VSS (V)
TA = 25C
5
VDD = 4V VDD = 3V VDD = 2V
1.5 1.0
1.5 1.0
VDD = 3V VDD = 1.8V VDD = 5.5V
4
.5 0 25C TEMPERATURE (C) 85C 0 1
VDD = 5.5V
.5 0
3 -40C
3 2 4 ISOURCE (mA)
5
6
0
1
2
3
4
5
6
ISINK (mA)
60 TA = -40C 50 40 TA = 85C 30 20 Sinking 10 Sourcing 0 0 REFERENCE VOLTAGE (V) TA = 25C
1.240
VDD = 1.8V VDD = 3V VDD = 5.5V
SUPPLY AND REFERENCE VOLTAGES (V)
Comparator Output Short-Circuit Current vs. Supply Voltage
OUTPUT SHORT-CIRCUIT CURRENT (mA)
Reference Voltage vs. Load Current
Line Transient Response of VREF
4
VDD
1.220 1.200 1.180 1.160
VDD = 1.8V
3
Sinking
TA
=
-4
0
C
Sourcing
2
VREF
TA = 25C TA = 85C 6
VDD = 5.5V VDD = 3V
1
1.140 0 2 4
0 0 100 200 TIME (sec) 300 400
3 1 2 4 5 SUPPLY VOLTAGE (V)
6
8
10
LOAD CURRENT (mA)
2002 Microchip Technology Inc.
DS21345B-page 7
(c)
TC1040
5.0 TYPICAL CHARACTERISTICS (CONTINUED)
Reference Voltage vs. Supply Voltage
1.25 REFERENCE VOLTAGE (V)
Supply Current vs. Supply Voltage
12 11 10 9 TA = 25C 8 7 TA = 85C TA = -40C
1.20
1.15
1.10
1.05 1 4 2 3 SUPPLY VOLTAGE (V) 5
SUPPLY CURRENT (A)
6 0 1 2 3 4 5 SUPPLY VOLTAGE (V) 6
(c)
DS21345B-page 8
2002 Microchip Technology Inc.
TC1040
6.0
6.1
PACKAGING INFORMATION
Package Marking Information
Package marking data not available at this time.
6.2
Taping Form
Component Taping Orientation for 8-Pin MSOP Devices
User Direction of Feed
PIN 1
W
P Standard Reel Component Orientation for TR Suffix Device
Carrier Tape, Number of Components Per Reel and Reel Size
Package Carrier Width (W) Pitch (P) Part Per Full Reel Reel Size
8-Pin MSOP
12 mm
8 mm
2500
13 in
6.3
Package Dimensions
8-Pin MSOP
PIN 1
.122 (3.10) .114 (2.90)
.197 (5.00) .189 (4.80)
.026 (0.65) TYP.
.122 (3.10) .114 (2.90) .043 (1.10) MAX. .016 (0.40) .010 (0.25) .006 (0.15) .002 (0.05)
6 MAX. .028 (0.70) .016 (0.40)
.008 (0.20) .005 (0.13)
Dimensions: inches (mm)
2002 Microchip Technology Inc.
DS21345B-page 9
(c)
TC1040
NOTES:
(c)
DS21345B-page 10
2002 Microchip Technology Inc.
TC1040
Sales and Support
Data Sheets Products supported by a preliminary Data Sheet may have an errata sheet describing minor operational differences and recommended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following: 1. 2. 3. Your local Microchip sales office The Microchip Corporate Literature Center U.S. FAX: (480) 792-7277 The Microchip Worldwide Site (www.microchip.com)
Please specify which device, revision of silicon and Data Sheet (include Literature #) you are using. New Customer Notification System Register on our web site (www.microchip.com/cn) to receive the most current information on our products.
2002 Microchip Technology Inc.
DS21345B-page11
TC1040
NOTES:
DS21345B-page12
2002 Microchip Technology Inc.
TC1040
Information contained in this publication regarding device applications and the like is intended through suggestion only and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. No representation or warranty is given and no liability is assumed by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement of patents or other intellectual property rights arising from such use or otherwise. Use of Microchip's products as critical components in life support systems is not authorized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, under any intellectual property rights.
Trademarks The Microchip name and logo, the Microchip logo, FilterLab, KEELOQ, microID, MPLAB, PIC, PICmicro, PICMASTER, PICSTART, PRO MATE, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. dsPIC, ECONOMONITOR, FanSense, FlexROM, fuzzyLAB, In-Circuit Serial Programming, ICSP, ICEPIC, microPort, Migratable Memory, MPASM, MPLIB, MPLINK, MPSIM, MXDEV, PICC, PICDEM, PICDEM.net, rfPIC, Select Mode and Total Endurance are trademarks of Microchip Technology Incorporated in the U.S.A. Serialized Quick Turn Programming (SQTP) is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. (c) 2002, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved.
Printed on recycled paper.
Microchip received QS-9000 quality system certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona in July 1999 and Mountain View, California in March 2002. The Company's quality system processes and procedures are QS-9000 compliant for its PICmicro (R) 8-bit MCUs, KEELOQ(R) code hopping devices, Serial EEPROMs, microperipherals, non-volatile memory and analog products. In addition, Microchip's quality system for the design and manufacture of development systems is ISO 9001 certified.
2002 Microchip Technology Inc.
DS21345B-page 13
(c)
WORLDWIDE SALES AND SERVICE
AMERICAS
Corporate Office
2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: 480-792-7627 Web Address: http://www.microchip.com
ASIA/PACIFIC
Australia
Microchip Technology Australia Pty Ltd Suite 22, 41 Rawson Street Epping 2121, NSW Australia Tel: 61-2-9868-6733 Fax: 61-2-9868-6755
Japan
Microchip Technology Japan K.K. Benex S-1 6F 3-18-20, Shinyokohama Kohoku-Ku, Yokohama-shi Kanagawa, 222-0033, Japan Tel: 81-45-471- 6166 Fax: 81-45-471-6122
Rocky Mountain
2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7966 Fax: 480-792-7456
China - Beijing
Microchip Technology Consulting (Shanghai) Co., Ltd., Beijing Liaison Office Unit 915 Bei Hai Wan Tai Bldg. No. 6 Chaoyangmen Beidajie Beijing, 100027, No. China Tel: 86-10-85282100 Fax: 86-10-85282104
Korea
Microchip Technology Korea 168-1, Youngbo Bldg. 3 Floor Samsung-Dong, Kangnam-Ku Seoul, Korea 135-882 Tel: 82-2-554-7200 Fax: 82-2-558-5934
Atlanta
500 Sugar Mill Road, Suite 200B Atlanta, GA 30350 Tel: 770-640-0034 Fax: 770-640-0307
Singapore
Microchip Technology Singapore Pte Ltd. 200 Middle Road #07-02 Prime Centre Singapore, 188980 Tel: 65-6334-8870 Fax: 65-6334-8850
Boston
2 Lan Drive, Suite 120 Westford, MA 01886 Tel: 978-692-3848 Fax: 978-692-3821
China - Chengdu
Microchip Technology Consulting (Shanghai) Co., Ltd., Chengdu Liaison Office Rm. 2401, 24th Floor, Ming Xing Financial Tower No. 88 TIDU Street Chengdu 610016, China Tel: 86-28-6766200 Fax: 86-28-6766599
Taiwan
Microchip Technology Taiwan 11F-3, No. 207 Tung Hua North Road Taipei, 105, Taiwan Tel: 886-2-2717-7175 Fax: 886-2-2545-0139
Chicago
333 Pierce Road, Suite 180 Itasca, IL 60143 Tel: 630-285-0071 Fax: 630-285-0075
Dallas
4570 Westgrove Drive, Suite 160 Addison, TX 75001 Tel: 972-818-7423 Fax: 972-818-2924
China - Fuzhou
Microchip Technology Consulting (Shanghai) Co., Ltd., Fuzhou Liaison Office Unit 28F, World Trade Plaza No. 71 Wusi Road Fuzhou 350001, China Tel: 86-591-7503506 Fax: 86-591-7503521
EUROPE
Denmark
Microchip Technology Nordic ApS Regus Business Centre Lautrup hoj 1-3 Ballerup DK-2750 Denmark Tel: 45 4420 9895 Fax: 45 4420 9910
Detroit
Tri-Atria Office Building 32255 Northwestern Highway, Suite 190 Farmington Hills, MI 48334 Tel: 248-538-2250 Fax: 248-538-2260
China - Shanghai
Microchip Technology Consulting (Shanghai) Co., Ltd. Room 701, Bldg. B Far East International Plaza No. 317 Xian Xia Road Shanghai, 200051 Tel: 86-21-6275-5700 Fax: 86-21-6275-5060
Kokomo
2767 S. Albright Road Kokomo, Indiana 46902 Tel: 765-864-8360 Fax: 765-864-8387
France
Microchip Technology SARL Parc d'Activite du Moulin de Massy 43 Rue du Saule Trapu Batiment A - ler Etage 91300 Massy, France Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79
Los Angeles
18201 Von Karman, Suite 1090 Irvine, CA 92612 Tel: 949-263-1888 Fax: 949-263-1338
China - Shenzhen
Microchip Technology Consulting (Shanghai) Co., Ltd., Shenzhen Liaison Office Rm. 1315, 13/F, Shenzhen Kerry Centre, Renminnan Lu Shenzhen 518001, China Tel: 86-755-2350361 Fax: 86-755-2366086
New York
150 Motor Parkway, Suite 202 Hauppauge, NY 11788 Tel: 631-273-5305 Fax: 631-273-5335
Germany
Microchip Technology GmbH Gustav-Heinemann Ring 125 D-81739 Munich, Germany Tel: 49-89-627-144 0 Fax: 49-89-627-144-44
San Jose
Microchip Technology Inc. 2107 North First Street, Suite 590 San Jose, CA 95131 Tel: 408-436-7950 Fax: 408-436-7955
Hong Kong
Microchip Technology Hongkong Ltd. Unit 901-6, Tower 2, Metroplaza 223 Hing Fong Road Kwai Fong, N.T., Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431
Italy
Microchip Technology SRL Centro Direzionale Colleoni Palazzo Taurus 1 V. Le Colleoni 1 20041 Agrate Brianza Milan, Italy Tel: 39-039-65791-1 Fax: 39-039-6899883
Toronto
6285 Northam Drive, Suite 108 Mississauga, Ontario L4V 1X5, Canada Tel: 905-673-0699 Fax: 905-673-6509
India
Microchip Technology Inc. India Liaison Office Divyasree Chambers 1 Floor, Wing A (A3/A4) No. 11, O'Shaugnessey Road Bangalore, 560 025, India Tel: 91-80-2290061 Fax: 91-80-2290062
United Kingdom
Arizona Microchip Technology Ltd. 505 Eskdale Road Winnersh Triangle Wokingham Berkshire, England RG41 5TU Tel: 44 118 921 5869 Fax: 44-118 921-5820
03/01/02
(c)
DS21345B-page 14
2002 Microchip Technology Inc.
*B54312SD*

▲Up To Search▲

Price & Availability of TC1040

	To Download TC1040 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .